Posted on: February 19th, 2016 by Sam Jacobs

Common noise sources and paths

Salon & Galley:
Engine noise through the deck
Engine noise through the bulkheads
Engine noise transmitted through air intake trunks
Structure-borne noise from engine & driveline
Propeller noise
Noise from your generator
Noise from your AC

Deck Spaces:
Engine noise through the deck
Structure-borne noise from engine & driveline
Engine noise through engine room vents
Exhaust noise
Propeller noise

Sleeping spaces:
Engine noise through the bulkheads
Structure-borne noise from engine & driveline
Noise from your generator
Noise from your AC
Noise from other cabins
Waves slap

Express – Under 30 ft

Over the past 30 years, Soundown has built up extensive experience in reducing noise aboard express boats. We’ve used that experience to develop this list of recommendations for dealing with the most common noise sources. While no two boats are the same, this list will get you on course towards a quieter vessel and a more enjoyable boating experience.

Each treatment description below includes recommended materials as well as the path it will treat (airborne and/or structure borne).

Treatment: Engine space insulation

Path: Airborne

Source: Engine

Improved areas: cabin, helm deck

Problem: The size of most express boats means most of your time aboard is spent in close proximity to the engines and generators. Whether on deck or inside, you are typically separated from the engine by only a single bulkhead or deck. As a result, a significant portion of the noise is airborne.

Solutions:

Reducing noise levels on board will require increasing the noise blocking ability (known as transmission loss) of the bulkhead or deck and sealing any penetrations where noise can leak out. Here are a few ways to accomplish that.

  • Barrier composite insulation on the overhead and bulkheads. Barrier composites sandwich a layer of mass-loaded vinyl with acoustic foam. The foam absorbs noise while the mass-loaded layer reflects noise back into the engine room, protecting accommodation areas.  Soundown’s IVF (insulated vinyl/foam) composite sheets are highly effective and are easy to install in new builds or during refit. Thicker is generally better if you have the space.absorptionmaterial

Best bet: 2” 2lb for diesel engines, 2” 1lb for gas engines

Specifications

  • EcoDamp is a flexible, self adhesive damping sheet that can be easily formed around pipes or wires to seal bulkhead and deck penetrations. Identifying and sealing all possible leaks is an essential step in reducing noise on your boat.
    ecodampOne technique for finding these gaps is to climb into the engine compartment, close the hatch and look for areas where you can see daylight (or a light source placed in the adjoining space, for interior bulkheads).  Any place where light can come through, noise can also leak out.
    Typically, you’ll find this leakage around plumbing and wiring. Eco Damp sheets are an excellent and flexible solution for this type of leakage. They feature an aluminum soft cover and are largely composed of self-adhesive rubber, which allows them to be shaped and molded to fill gaps and create barriers that can be removed later as needed.

Best bet: EcoDamp

Specifications

  • Gaskets around hatches are critical in reducing leakage which allows room noise to leak out into other spaces. Make sure that when each hatch is closed, the seals are tight. You inspect a hatch’s seal by trying to slide a business card between the hatch and deck. If you can get it into the seam, the Gasket isn’t tight enough.
    Where possible, you want the gasket on the hatch itself – it will take a lot less wear and tear there. It’s also best to get D-profile or finger-top style rubber gaskets. These seal well across a wider variety of gaps than solid gaskets. it’s rare that the gap between deck and hatch is consistent all the way around, so the best gaskets are flexible enough to handle irregularities.
  • For vessels with fuel tanks outboard of the engines we recommend Soundown’s IAF acoustic foams. IAF does not feature a barrier – the foam absorbs reverberant noise in the machinery space resulting in lower levels of noise transmitted throughout the boat.

Best bet: 1”

Specifications

  • For a high level of finish and additional noise reduction, Soundown QuieTech perforated aluminum sheets can be installed over the insulation.quiettech1

Specifications

Treatment: Engine space noise leaking through bulkheads

Path: Airborne & structure-borne

Improved areas:  Cabin forward of engine room

Problem: Depending on the proximity of the cabin to the engines, good engine room insulation may not be enough. This culprit is typically the high level of structure-borne vibration in the bulkhead which radiates into the cabin.

Solutions:

  • Gaskets around the bulkheads are also a great solution to leaking engine room noise (see machinery space above).

Best bet: Neoprene Gaskets

Specifications

  • Isolating or “floating” the interior panel. By floating the interior panel, we can break the path of that vibrational energy, reducing interior noise.
  • The detail below shows a floated bulkhead.BULKHEADGROUP

Specifications

Treatment: Engine vibration transmitted through the hull

Path: Structure-borne

Improved area:  All areas

Problem: The lightweight construction typical of cruisers, combined with the high horsepower of their engines, means significant vibration can be created while the engine does its job. Smaller cruisers don’t really lend themselves to Isolation mounts, but larger cruisers may have room in the engine compartments.

Solutions:

  • Isolation Mounts for the engine. These decouple the engine from the hull, isolating a significant portion of the vibration. While there are many options that can be considered, space constraints usually mean that engine and gear boxes are close coupled and require a mount that can handle the force of the propeller thrust. The Rubber Design TT mounts (thrust & torque) are designed specifically for such applications. The TT’s unique design uses a series of rubber plates in shear, to provide isolation when positively or negatively loaded. By combining size and rubber stiffness options, Soundown can select a mount that avoids excessive engine movement while providing ideal vibrational isolation.

Specifications

Wave slap